Regardless of the number of bands, only the most advanced drivers can be found in each of the frequency registers of the Victa Elite speakers. The cone drivers for mid and low frequencies use the renowned technology of a diffuser made of long-fiber kraft paper, with a concave dust cap made of the same material. This technology, well known from various HECO series, with an optimal combination of high damping qualities of the diffuser and low mass at a given rigidity, has once again confirmed its exceptional sound qualities. Equipped with powerful ferrite magnets and an improved voice coil resistant to high loads, the speakers demonstrate a deep, dense bass and a clear, transparent sound picture.
HECO Victa Elite 202
Depending on the size, the speakers have eight or six mounting points on a thoroughly reinforced mounting flange. The HF speakers with a 25 mm silk dome use ferrofluid cooling, which effectively increases the reserve of permissible power. The large, rectangular, rounded outer flange of the HF speaker acts as a horn acoustic load and contributes to reducing distortion, expanding the radiation angle, and matching with the underlying midrange register. The high-quality crossover uses amplitude and phase matching of frequency registers, which brings outstanding integrity and homogeneity of sound across the entire operating frequency range of the speaker system.
![VictaElite-Serien-Slider[59] (1).jpg](https://www.stereoindex.com/wp-content/uploads/2025/08/3c21e9b3ceecb99f363c6782c5e89677.jpg "VictaElite-Serien-Slider[59] (1).jpg")
The outstanding design of the HECO Victa Elite is notable for its curved, non-parallel sides that converge towards the rear. This solution is very advantageous from an acoustic point of view, eliminating the risk of standing waves inside the cabinet. The sides are made of bent-glued MDF panels, while the remaining elements of the cabinet are represented by solid flat MDF panels.
Along with the traditionally impeccable quality of workmanship, the cabinet with internal power struts is distinguished by high rigidity and the absence of parasitic resonances. In addition, the design of the cabinet provides close to ideal operating conditions for the speakers, and in the LF section it acts as an acoustic design with a phase inverter that effectively adds bass depth. The cast aluminum ports of the phase inverters are located on the rear panel of the cabinet and are secured with screws. The optimal profile of the phase inverter eliminates the appearance of extraneous sounds when working at any volume, and the character of the sound in the lower register is distinguished not only by impressive depth, but also by excellent speed data. At the bottom of the floor-standing speakers of the series is the base of the case made of a solid thick MDF plate. During the development of HECO Victa Elite, the enlarged connection panel with high-quality gold-plated connectors was significantly modified to achieve maximum connection quality with high ergonomics. Complete anti-resonance rubber feet serve as a stable installation in the chosen place, and the floor-standing speakers of the series are also equipped with metal spikes of adjustable height.
HECO Victa Elite 202
HECO Victa Elite 202 are the most compact among the shelf speakers of the series. Thanks to Heco technologies, these small speakers hide significant advantages. The 120 mm LF/MF speaker cone is made of a material that has proven itself in many Heco series: long-fiber kraft paper. This guarantees a clear and precise sound over a wide frequency range, even with the most complex musical compositions. Along with a lightweight 20 mm silk dome, the HF speaker design includes ferrofluid cooling for increased power handling, as well as a metal outer flange that acts as a horn acoustic load. This design technique improves the directivity pattern at high frequencies, as well as coordination with the underlying midrange register. The body is assembled from MDF panels and thoroughly reinforced to combat unwanted vibrations. The curved non-parallel (converging towards the rear) sides of the body emphasize the originality of the design, and are also very advantageous from an acoustic point of view, eliminating the risk of standing waves inside the body.
HECO Victa Elite 202 Specifications:
- Number of bands 2
- Power 60 W
- Maximum power 100 W
- Separate connection of LF and HF (Bi-wiring) yes
- Recommended amplifier power 20-100 W
- Sensitivity 89 dB
- Impedance 4-8 Ohm
- Frequency range 36-38000 Hz
- Crossover frequency 3.5 kHz
- Power amplifier connector screw Gold
- -plated connectors yes
- Emitter type dynamic
- HF emitter 20 mm, dome
- LF emitter 120 mm, cellulose
- Body material MDF
- Removable grille
- Dimensions (WxHxD) 165x265x230 mm
- Weight 3.2 kg
